英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

handwheel    

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Handwheel does not turn or is tight - Brother USA
    Handwheel does not turn or is tight Objective Handwheel does not turn or is tight Procedure CAUTION The handwheel on the machine should turn freely By forcing the hand wheel to turn, you could do further damage to your machine
  • Handwheel does not turn or is tight - Brother USA
    The machine is in a bind and cannot turn freely Follow these steps to loosen the hand wheel: 1 Turn power switch off position 2 Remove the needle in the machine 3 Turn hand wheel toward the back of the machine to break the machine loose from the tight spot 4 Now try to turn the hand wheel toward the front of the machine If the problem persists, your machine may require service Check
  • Change or replace the needle - Video included - Brother USA
    Images may differ depending on the model, but the overall process is the same 1 Raise the needle using one of the following methods: - Turn the handwheel toward you (counterclockwise) so that the mark on the wheel points up
  • Remove a needle that has fallen inside the machine - Brother USA
    - Turn the handwheel to check that the feed dogs move smoothly and do not contact the edges of the slots in the needle plate If the steps are not completed in this manner it may cause issues when trying to tighten the screws back on the needle plate 11 Insert the bobbin case back into the machine
  • Oiling the machine - Video Included - Brother USA
    How to oil the needle bar 1 Select one needle bar at a time from the embroidery screen 2 Turn the handwheel counterclockwise bringing the needle bar to its lowest position 3 Put one drop of oil, as high as possible on the needle bar above the felt washer
  • Noise - Brother USA
    Check the Feed Dogs 1 Stop your machine and turn off the power 2 Turn the handwheel until the needle is in the up position 3 Check the feed dogs - If the feed dogs are too high or too low, it could cause grinding or unusual noises - Check for dust in the feed dogs 4 Turn the handwheel and confirm that the handwheel turns easily - If the handwheel does not turn easily, do not turn on
  • How to start sewing - Video Included - Brother USA
    2 Raise the needle by turning the handwheel toward you so that the mark on the wheel points up 3 Turn the pattern selection dial to select a stitch 4 Change the presser foot 5 Raise the presser foot lever 6 Place the fabric under the presser foot, pass the thread under the presser foot, and pull out about 2 inches of thread toward the rear of the machine 7 While holding the end of
  • How to set the stitch length and the stitch width - Video Included
    - After adjusting the stitch width, slowly turn the handwheel toward you (counterclockwise) and check that the needle does not touch the presser foot If the needle hits the presser foot, the needle may bend or break
  • How to thread the upper part of the machine - Video Included
    Follow the instructions below to thread the upper thread: - Click here for video instructions 1 Turn the machine off 2 Raise the presser foot lever 3 Raise the needle by turning the handwheel toward you, so that the mark on the wheel points up - If the needle is not correctly raised, the sewing machine cannot be threaded 4 Pull up the spool pin and put a spool of thread on this pin





中文字典-英文字典  2005-2009