英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字,中文词皆可:



安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Question on wads: straight vs taper - Cast Boolits
    It did chamber ok, not loose, but dropped in I then cut a window to check to make sure the seal was on the powder It is seated all the way on the powder, but as you can see, the gas seal is cocked slightly These wads were the Claybuster 2100-12, Federal 12S0 clone Gas seal measures about 722", slightly out of round, as are most wads
  • My (bad) experience with Walters wads. - Cast Boolits
    I learned about LDPE wads here and wanted to try them in my black powder cartridges, but in Italy I had a hard time finding LDPE in sheets So I read about Walter wads and asked him if he could send 4 bags of 1000 wads each to Italy I was told that it was possible and that the shipping cost would be around $28
  • Are over the powder wads necessary? - Cast Boolits
    Card wads were of vegetable and paper (milk carton) using bought and home made from 002 through 006" thickness I found not difference in accuracy (2 foulers then 10 shot groups) at 200 or 300 yards between loads with card wads over the powder and when none was used Hence, I do not bother with a card wad over the powder
  • What wad material to use - Cast Boolits
    I use wads cut from serial boxes and OJ cartons as well as thin dense cork and fiber gasket material as well There is a reason I like to use plastic and cork over the others is, The plastic and cork seals the bore better when the charge goes off
  • I am wanting to Make My Own Wads Seals - Cast Boolits
    I use leather about 1 8" thick to punch out 3 8" ( 375) wads for use in my 36 caliber cap handball revolvers - I punch them out - melt down in the microwave my BP lube (1# can of crisco mixed with one real beeswax toilet bowl ring) - melt it in the microwave, soak the wads and then pat dry between paper towel or newspaper - work great for over
  • Wads under Hollow base. - Cast Boolits
    Thread: Wads under Hollow base Thread Tools Show Printable Version; 06-13-2025, 07:28 PM #1 Martini
  • 50 cal wads - Cast Boolits
    I made some leather wads from the leather that I got from you a few days ago I punched them out using a half inch hollow punch The rifle was a 50 cal Hatfield I was using 50 grains of Goex fffG My patches were 015 light denim that were lubricated with Bore Butter I soaked the wads in Balistol and let them dry on a towel for about three days
  • Wad Suggestions for 00 Buckshot - What are your favorites . . . - Cast . . .
    Powders - Unique, Longshot, and H Universal Wads to include, MG42, Original Brush Wads, WAA12, 12S3, Verslite I'm doing my shopping at Ballistic Products Already have their Buckshot "manual", which was near useless Found one recipe and it patterned minute of barn door I would love to hear what wads you guys prefer for 00 buck loads
  • wad making. . . - Cast Boolits
    If you buy fiber and cork and card wads, the cost of the various wads needed in combination to make a workable load (overpowder, cushion, and possibly overshot) will exceed the cost of the single plastic wad you can buy, especially from the lower cost suppliers like Claybuster and Downrange purchased in lots of 1000 to 5000 at a time
  • Best wad for general purpose buckshot loads in 12 guage? - Cast Boolits
    A single bag of 250 wads would probably last me a good long while So what's the best one to get for loading medium payload 2 3 4" shells with #4, #0, and #00 buckshot? It seems like the Winchester wad (WAA12) that supports 1oz - 1 5 8oz loads might be a good place to start, but I'm basically shooting from the hip here and I'm anxious to hear





中文字典-英文字典  2005-2009