英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字,中文词皆可:


请选择你想看的字典辞典:
单词字典翻译
chymical查看 chymical 在百度字典中的解释百度英翻中〔查看〕
chymical查看 chymical 在Google字典中的解释Google英翻中〔查看〕
chymical查看 chymical 在Yahoo字典中的解释Yahoo英翻中〔查看〕





安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Wood Bending by Kerfing - Lost Art Press
    Normally a minimum value of at least three-quarters of the thickness of the material is chosen, provided the thickness of uncut wood is not reduced below 1∕16 in minimum (Fig 4) Kerfing, therefore, is only logically applicable to wood thicknesses of from 1∕4 in upwards Best thickness for good results appears to range between 5∕8 and
  • Linings kerfing what do you think - Delcamp Classical Guitar Forum
    Linings kerfing what do you think and at the top I cut regular Spanish cedar kerfed linings into small pieces of about 3-4 peones just enough to be able to press them well with 2 fingers using hide glue Side thickness seems not to matter I've used the solid linings with sides from 1 8 to 2 5mm with no noticeable difference Overall
  • Effect of Kerfing and Incising Pretreatments on High-Temperature Drying . . .
    Effect of Kerfing and Incising Pretreatments on High-Temperature Drying Characteristics of Cedar and Larch Boxed-Heart Timbers with Less than 150 mm in Cross Section Size - 347 - Fig 1 Processing diagram of the specimens ((a) in-cising, (b) longitudinal kerfing, (c) final MC distri-bution) Stage Time (Hours) Dry-bulb (℃) Wet-bulb (℃) 1
  • Kerfing – Bending wood on the tablesaw | Stus Shed - WordPress. com
    Divide this amount by the thickness of the saw blade This gives the number of saw cuts 3 Last, divide the Outside Perimeter of the radius by the number of saw cuts kerfing works well but better with timber with above 12% moisture content, green oak works every time, iroko too! But when workin with curved frames I tend to strengthen the
  • Making the kerfing - sillars. com
    I started the kerfing by milling two pieces of straight-grained Spanish cedar, 1 4" thick by 1-1 2" wide, by 33" long One of these pieces is shown to the right I measured the thickness of a 3d finish nail and found it to be slightly larger than 1 16" I drilled a 1 16" hole in my jig for the 3d nail; the final height of the pin cannot be
  • Back lining - solid, kerfing, basswood, cedar, rosewood? - Delcamp . . .
    The self-linings, using side cut offs, looks nice, and, being the same thickness as the sides, are easily bent But then you need to laminate them to get to a workable lining thickness Willow seems to bend OK at lining thickness, but I have had trouble bending other woods, such as basswood, at that thickness
  • Guitar Kerfing VS Solid Linings - The Art Of Lutherie
    Tom Bills Tom Bills has been hand crafting one of a kind custom guitars for the top players and collectors around the world since 1998 Tom is also the author of the guitar making book DVD set - The Art Of Lutherie - published by Mel Bay, and has written for and been featured in may publications both in print and online as well as several television and film spots
  • Alis Guitars: Linings Kerfing
    Linings Kerfing The linings are the wooden pieces on the inside of an acoustic guitar that have the kerf cuts in them so they can easily be bent to match the curvature of the guitar sides Its difficult to do when I have to take the wall thickness down to 2mm in order to bend them where I need to, so i use a variety of methods to get this
  • Kerf Bending - Wood
    Before you start kerfing the apron stock for our table, make the bending form, shown on Drawing 4, below To do this, cut three 24×48" pieces of 3 ⁄ 4" plywood, particleboard, or medium-density fiberboard (MDF) Draw a centerline across the 24" dimension of each piece Mark a point on this line 1 3 ⁄ 4" in from one edge
  • Bending Wood Panel Kerf Formula – The WVb
    Divide this amount by the thickness of the saw blade This gives the number of saw cuts Last, divide the Outside Perimeter of the radius by the number of saw cuts This gives the distance between saw cuts I have put all of this into an excel spreadsheet to make it very easy for you Kerf Formula I hope this has been both informative and helpful





中文字典-英文字典  2005-2009