英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字,中文词皆可:


请选择你想看的字典辞典:
单词字典翻译
58711查看 58711 在百度字典中的解释百度英翻中〔查看〕
58711查看 58711 在Google字典中的解释Google英翻中〔查看〕
58711查看 58711 在Yahoo字典中的解释Yahoo英翻中〔查看〕





安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Frame Transmission Crossmember Thickness, Size???
    I preger either 125 or 10 gauge depending on if I am bending up my own from sheet metal or using tubing 1 16 or 0625 is probably a stretch unless it is not going to see much heavy pounding porknbeaner , Jul 25, 2012
  • Tubing thickness for frame crossmembers? | CK5. com
    I'm looking at 2" tube up front, which will span the gap between the front crossmember spring mounts From what I've seen these can tend to be a bit of a problem area, so I figured 120" would be a safe bet I'd like larger diameter, but that would interfere with the mounts
  • cross member material and strength advice - Pirate 4x4
    my current idea is to make it out of 1" x 3" x 25" box tubing 1" will be the height of the crossmember and 3" will be the width
  • Steel tubing for frame and other questions | Hot Rod Forum
    I'm using 2" x 3" x 1 8" retangular tubing for the trans brace and 3 16" plate for the center one Take your time welding it and pre-measure the width of the frame for referance Get it level so you can check it for warping by measuring from the floor Also if you haven't welded alot get a buddy who has and is capable of doing this kind of work
  • DIY: Weld-in transmission cross-member and transfer case skid
    I chose a center tube of approximately 14" as it's what I had on-hand and it didn't interfere with anything The fundamental part is you mount a larger tube in center slide in the wings in order to allow you to perfectly nail the span measurement frame to frame and mount to your bushings
  • Hot Rods - Home made Chassis | The H. A. M. B. - The Jalopy Journal
    For cross members like for coil over mounts or shock mounts I would use 2 or 3" tubing Your choice from cross members is dependent on what type of cross member you are using Building the frame is my favorite part of the project I like to use 3 16" wall rectangle tubing
  • Is there a suggested wall thickness for steel tubing when . . .
    If building for a street vehicle, according to this forum post, they say that for 2x3, 2x4, and 2x5, 0 120" wall rectangular tubing is more than adequate for car frames If you have to go a bit thicker to find what you want, even better
  • building a transmission crossmember | Turbobricks - The Volvo . . .
    I'm planning on building a transmission crossmember It's for a muncie (old school 4 speed) into a 245 I'll have to push the transmission up so i'm
  • Universal Transmission Crossmember - ThorBros. com
    This kit allows you to install a transmission crossmember where you want it! The tubing size is 1 5" OD, with a 7 32" wall thickness All Grade 8 hardware is included Tubing Length 36"
  • Transmission Cross members - Proffitt\s Resurrection Land . . .
    There are usually too many variables going on where the crossmember needs to go for a “one size fits most” part Engine placement, front driveshaft, exhaust routing, frame width, fuel and brake lines, and more all make it so that each crossmember would need to be a little bit different





中文字典-英文字典  2005-2009